Click Here To Find Out More

 

The content following next involving How to Install a Bathtub Yourself is extremely stimulating. Check it out for your own benefit and decide what you think about it.

Installing a bathtub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately difficult job. If the old tub is readily available, the project can move quickly; if you have to open a wall surface to get rid of the old bathtub and also place the new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will require a helper to leave the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the task and also fit trying it. As opposed to employing a contractor to take over a halfway-completed job, it is much better to consider using one before you begin. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your bathroom if you have currently acquired a brand-new bathtub and do not need to change the plan of your previous water system pipelines.
Your devices and material list must make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining structure supplied with the bath must be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to prevent pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last position.

 

 

Removing Old Touches

If you require to change old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic due to the restricted gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

 

 

Installing the Bath tub

Utilizing both wood boards under its feet, put the bath tub in the required position. The wood boards are handy in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bathtub up until the spirit level reviews level.
To mount taps, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if needed. Fill up the bath tub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub ought to wait up until the tub has actually been made use of at least once as this will settle it right into its last placement.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the faucet and also the sink. Safeguard the tap in position with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type should be attached to the tap finishes first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the area where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, creating the water to permeate the wall between the bath and also the tiling, resulting in issues with wetness and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and also installations. They are marketed in tubes and also cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealant can crack relatively very early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is a good idea to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I hope you liked our article about Installing A Bathtub. Thanks a ton for finding the time to browse our piece of content. Appreciated our blog? Please share it. Let another person locate it. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Visit Homepage